Pump Division caters to the requirement of pumping system of the contractors. Contractors can be broadly classified into MEP contractors, Irrigation contractors, Air conditioning contractors, STP contractors, Swimming pool contractors etc. Though the general assembly and materials used are similar, the logic of operation differs from case to case basis. Depending upon application, the packaged pump sets are divided into the following categories.

BOOSTER PUMPS
These are used to increase the pressure of the water being pumped. As an example, take the case of a four-storied building, where water tank is situated on the top of the roof. The pressure of water will be sufficient up to the third floor, but the top floor will not have enough pressure. Here we have to fix a pump to increase the pressure. In some cases, it will not be possible to construct a water tank on the roof due to various reasons. In such cases we have to install a pump to provide water to all out lets. For irrigation pumps also the basic principle is the same, however, we have to increase the pressure which is compatible with the sprinklers, drip, solenoid valve etc used for irrigation.

PUMPS	Machine to increase the pressure
PRESSURE SWITCH	Digital sensor to give on and off command to the control panel(and in turn to the pump)
PRESSURE VESSEL	This is a pre charged tank either metallic or fiber glass, with a rubber bladder inside. When in operation, water enters into the bladder. The pressure of water inside is balanced by the backpressure of air in the tank. The function of pressure vessel is (1) to keep the line pressurized, so that the fluctuation of pressure inside the manifolds are minimized (in order that pressure switch will not get erratic signals) and (2) to control the number of starts and stops of the pump by supplementing the water it carries.
VALVES	To control the flow
PRESSURE GAUGE	To note the pressures
FLOAT SWITCHES	These are used to stop the pump automatically, when there is no water in the suction tank (dry run protection.) Manifolds: to provide a common path for the suction and discharge of each pump.
CONTROL PANEL	This provides the logic of operation for the pumps. It mainly contains main circuit breakers, control cbs, contactors, over load relays, auxiliary relays, timers etc.
BASE FRAME	All the above components are assembled on a common base frame and supplied as one unit.

TRANSFER PUMPS
This is used to lift water from one tank to another, may be from a ground tank to an overhead tank. The construction is similar to the booster pumps, with some variations. Here pressure switch and pressure tank are absent. The operation of the pumps is controlled by either the float switch kept on the OH tank or timers. If the pump is controlled by float switch, the pump will start when float is at a lower level and stop when it is at higher level. If the pumps are controlled by timers, the pump will continue to work as per the timer settings.

CHILLED WATER PUMPS
They are used in AC application. In multistoried buildings, air conditioning is based on chilled water principle. Chilled water pumps circulate the water through the pipes and heat exchanger. They are generally large end suction or Horizontal split casing pumps running at 1450 rpm. The pumps are coupled to the motors and supplied as one unit.

SEWAGE PUMPS
These pumps are used for emptying sewage pit, storm water or drainage applications. There are different types of sewage pumps. Sewage pumps are used for building services and treatment plants. Generally pumps are supplied with a control panel that is different from the above-mentioned panels. Four float switches, placed at different levels in the tank, control the logic of operation. The panels are fitted with audiovisual alarms.

SWIMMING POOL PUMPS
Swimming pool pump can be classified into two. (1). The pumps used for re-circulation and filtering. These pumps are normal pumps with a strainer attached to the suction. (2). Heat pumps. These are used to control the temperature of water in the pools. During summer, it will cool the water and during winter it will heat the water. Apart from this, heat pumps are used in villas for cooling the water inside their tank. We have a good range of heat pumps.

PRODUCTS LIST- PUMP DIVISION
Supply of all type of water pumps & packaged pump sets
Fabrication of all type of water pump sets, as per the client' specification
Prompt repair & maintenance of pumps and packaged pump sets at site

WATER PUMPS	WATER PUMP SETS
Pumps Brand & Make	Packaged Pump Sets
GRUNDFOS - DENMARK	TRANSFER PUMP SETS
ARVEN - ITALY	BOOSTER PUMP SETS
ESPA - SPAIN	SUBMERSIBLE SUMP PUMP SETS
SPERONI - ITALY	SEWAGE / DRAINAGE PUMP SETS
NOCCHI - ITALY	PRESSURIZATION PUMP SETS
SAER - ITALY	CHILLED WATER PUMPS
LOWARA - ITALY	HOT / COLD WATER CIRCULATION PUMP SETS
EBARA - ITALY
ALL OTHER PUMPS AS PER YOUR SPEC.	ALL OTHER PACKAGED SETS AS PER YOUR SPEC

ACCESSORIES & OTHER PRODUCTS
Items	Make
GRUNDFOS PRESS CONTROL	ITALY
RESSURE PLUS PRESS CONTROL	ITALY
PRESSURE SWITCH SQUARE-D	ITALY
ESSURE GAUGE	ITALY
FLOAT SWITCH	GERMANY / ITALY
GLOBAL WATER SOLUTIONS PRESSURE VESSELS	U.S.A. / TAIWAN / TURKEY
PRESSURE VESSELS – CIMM / NEMA / ELBI / WATES	ITALY / TURKEY
WATER HEATERS – OPUS / HOTPLUS	ITALY / EGYPT
SUBMERSIBLE MOTORS - FRANKLIN	GERMANY
ELECTRIC MOTORS – VEM / ABANA	GERMANY / TURKEY
CABLE FOR SUBMERSIBLE PUMP – PYRISMIAN	GERMANY
CRESCENT DUCTILE IRON MANHOLE COVER	INDIA
METAL ENCLOSURE FOR CONTROL PANEL	CHINA
ALL OTHER ACCESSORIES RELATED TO OUR SCOPE OF SUPPLY